With the grates removed, brush down the inside to clear out any loose particles that have collected in the bottom and around the sides. Scrape off any large peeling flakes of carbon and grease and if yours is a charcoal grill, empty the ash catcher. Don’t forget to clean the drip pan and grease cup in warm soapy water and line them with aluminum foil so they’ll be easier to clean next time.
You also want a cooler, medium heat area of the grill to move the steaks to once they're seared and crispy on the outside. If you have enough burners and space on your grill, set them to a lower heat; if you don't have enough room, simply turn off the burner. If you are using a charcoal grill, one side should have a hot fire while the other a smaller, cooler flame.
With the grates removed, brush down the inside to clear out any loose particles that have collected in the bottom and around the sides. Scrape off any large peeling flakes of carbon and grease and if yours is a charcoal grill, empty the ash catcher. Don’t forget to clean the drip pan and grease cup in warm soapy water and line them with aluminum foil so they’ll be easier to clean next time.
After the grates and panels have soaked, take them out and scrub them thoroughly. A long handled grill brush offers added leverage. For really stubborn gunk, a paste of vinegar and baking soda helps the brush scrub off the worst bits. Rinse them clean. Take care to thoroughly dry cast-iron grates. Now’s a great time to inspect porcelain grates for chips that may lead to rust later on.

If you've purchased a new Weber grill, the company says that seasoning the cast iron grates isn't necessary. A porcelain enamel coating is already added to the cast iron so you don't need to season it at all. Instead, they recommend that when using a grill for the first time, you turn up the heat for about 15 minutes, then brush it clean with a stainless steel bristle brush.

Transfer the steaks to cooling racks with a sheet pan or cookie sheet underneath, cover the whole tray with plastic wrap and stick them in the fridge. Take them out about 30 minutes before cooking, pat them dry again with paper towels (because the salt will pull out some juices), season with freshly ground black pepper (press the pepper into the meat as you did with the salt) and then grill as you normally would. We'll talk more about black pepper in a moment. As for patting the steaks dry, a dry steak will form a browner crust when it's cooked.
Yes, you should touch the steaks to test for doneness, but that doesn't mean that you should be flipping and moving and poking a lot. Steaks should only be flipped once, and only moved once from a higher to a lower heat. And don't poke them with anything but your finger! Put the meat on a hot grill—they should sizzle immediately—and leave them there until they release on their own accord. If you're pulling or struggling with them, they are not seared and not ready to flip.
For metal and cast iron grill grates, coat lightly with a high temperature oil like Canola or Peanut oil – wipe off any excessive oil, install the grates and fire up the grill.  Heat the grill on high and let it burn for ~30 mins.  This will burn all the solvents and impurities off of the heating elements, grill grates, etc.  Note that porcelain grates won’t need a coat of oil, but will benefit from the burn in process to remove any chemicals/impurities that were applied by the manufacturer. 
You also want a cooler, medium heat area of the grill to move the steaks to once they're seared and crispy on the outside. If you have enough burners and space on your grill, set them to a lower heat; if you don't have enough room, simply turn off the burner. If you are using a charcoal grill, one side should have a hot fire while the other a smaller, cooler flame.
Check the fuel lines for invisible openings. Create a mixture of soap and water. Make sure you stir the mixture around so it gets really sudsy. Then, use a paintbrush to brush the soapy mixture onto the fuel lines.[6] Turn on the gas, and brush some more soapy water onto the gas lines. If any bubbles form on the gas lines, that indicates a gas leak. Immediately replace any fuel lines that exhibit signs of a gas leak.
×